Genuine BMW 328i Fuel Pump

BMW 328i Fuel Pump Parts Questions & Answers

• Fuel Pump Fuel Tank Mounted
  16-11-7-243-975
  Q: How to remove and install the fuel level sender and fuel pump assembly in a BMW 328i?

  A: There are two level senders installed in the fuel tank - one on each side. The pump is integral with the right-hand side sender, and at the time of writing, the pump and sender can only be replaced as an assembly. Check with a BMW dealer or parts specialist. Before removing the fuel level sender and fuel pump assembly, all fuel should be drained from the tank. Since a fuel tank drain plug is not provided, it is preferable to carry out the removal operation when the tank is nearly empty. Remove the rear seat cushion. Fold back the insulation material to expose the access cover. Remove the mounting nuts, and remove the access cover from the floor. Through the access hole, disconnect the electrical connectors, then depress the release button and disconnect the vent hose from the fuel level sensor and fuel pump cover. Be prepared with a container to collect fuel spillage. Unscrew the fuel level sender and fuel pump assembly locking ring and remove it from the tank. Although a BMW tool (No 16 1 020) is available for this task, it can be accomplished using a large pair of pliers to push on two opposite raised ribs on the locking ring. Alternatively, a home-made tool can be fabricated to engage with the raised ribs of the locking ring. Turn the ring counter-clockwise until it can be unscrewed by hand. Make an alignment mark between the collar and the tank to aid reassembly. Carefully lift the fuel level sender and fuel pump assembly cover from the tank. Disconnect the vent hose and wiring plugs from the base of the cover. Note how the rods in the base of the cover are mounted in the assembly. Do not detach the black plastic wire connection between the cover and the pump unit - it's essential to stop the pump unit floating away during reassembly. Noting their installed locations, disconnect the hoses from the assembly. Carefully maneuver the pump/sensor unit from the tank. Take great care not to bend/damage the float arm as the unit is withdrawn. If required, the level sensor can be unclipped from the pump assembly. On full deflection, the sender resistance should read 993 ohms, and on zero deflection, the resistance should read 51 ohms. For the left-hand fuel level sender, fold back the insulation material to expose the access cover. Remove the access cover mounting nuts and the cover from the floor. Disconnect the wiring plug from the sensor unit cover, then pull the locking collar away and disconnect the fuel supply pipe. Unscrew the fuel level sender locking ring and remove it from the tank. Although a BMW tool (No 16 1 020) is available for this task, it can be accomplished using a large pair of grips to push on two opposite raised ribs on the locking ring. Alternatively, a homemade tool can be fabricated to engage with the raised ribs of the locking ring. Make an alignment mark to reference the ring to the tank before rotating the ring. Rotate the locking ring counterclockwise until it can be unscrewed by hand. Tie a length of string or wire around the disconnected hoses accessible through the right-hand tank access hole, as these hoses will be removed with the left-hand fuel level sender. The idea is to pull the string or wire into the tank as the sender is removed, then leave it in place to facilitate installation. Carefully lift the sender from the tank, and remove it. Untie the string or wire and leave it in place. For installation, installation is the reverse of removal, noting the following points: Use a new sealing ring. To allow the unit to pass through the aperture in the fuel tank, press the float arm against the fuel pick-up strainer. When the unit is installed, the locating lug on the unit must engage with the corresponding slot in the fuel tank collar, the raised ribs of the locking ring. Make an alignment mark to reference the ring to the tank before rotating the ring. Rotate the locking ring counterclockwise until it can be unscrewed by hand.
• Fuel Pump Fuel Tank Mounted
  16-11-7-243-975
  Q: How to remove and install a high-pressure pump?

  A: To remove the fuel system, start by relieving the fuel system pressure and disconnecting the negative battery cable. Then, remove the engine cover, strut tower crossbrace, and sound insulator. Next, remove the ignition coils and disconnect the high-pressure line pipe fittings. Loosen and disconnect the feed pipe fitting on the high-pressure pump, and disconnect the electrical connector from the pump. Loosen the high-pressure fuel pump bolts and remove the pump, making sure to replace the bolts and O-ring. To install the pump, ensure the camshaft lobe is at its Bottom Dead Center (BOC) base circle. Lubricate and install the bucket tappet, then set the pump into the cylinder head and tighten the bolts evenly. Finally, reconnect the negative battery cable, start the engine, and check for fuel leaks.