How to remove the rear and front driveshaft on BMW 328i?

To remove the rear driveshaft, block the front wheels and raise the rear of the vehicle on jackstands. Remove the exhaust system and heat shield, and if necessary, unbolt the exhaust system mounting bracket. Make alignment marks between the shaft, transmission flange, and rubber coupling. Loosen and remove the nuts and bolts securing the coupling to the transmission. Make alignment marks between the driveshaft and differential flange, then unscrew the bolts securing the driveshaft to the rear differential. With the assistance of an assistant, support the driveshaft and unscrew the center support bearing bracket retaining bolts. Lower the center of the shaft and disengage it from the transmission and rear differential. Remove the shaft from underneath the vehicle. Inspect the rubber coupling, support bearing shaft, and universal joints. Inspect the transmission flange locating pin and driveshaft bushing for signs of wear or damage. Replace any worn or damaged parts. Rotate the support bearing to check for smooth turning and replace if difficult or gritty. Apply moly-based lubricant grease to the transmission pin and shaft bushing, then maneuver the shaft into position. Align the marks made prior to removal and engage the shaft bushing with the transmission and rear differential unit flanges. Install the bearing support bracket retaining bolts, tighten the rear coupling bolts, and install new retaining nuts. Tighten the support bracket bolts. Install the exhaust system. To remove the front driveshaft on AWD models, block the rear wheels and raise the front of the vehicle on jackstands. Remove the engine splash shield and front subframe reinforcement panel if equipped. Make match-marks on the front differential flange and the front of the driveshaft, as well as the rear of the driveshaft and the flange at the transfer case. Remove the bolts securing the driveshaft front yoke to the differential flange, then remove the bolts securing the driveshaft rear flange to the transfer case. Remove the driveshaft from the vehicle. Installation is the reverse of removal, replacing any zinc-plated aluminum bolts.

Genuine BMW 328i Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Series

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Drive Shafts found

View related parts
BMW 328i Automatic Gearbox Drive Shaft
Part Number: 26111229565
$1299.83 MSRP: $1626.78
You Save: $326.95 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Drive Shaft Gearbox; Drive Shaft
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1999-2000 BMW 328i | Sedan(E46)
View related parts
BMW 328i Five Speed Gearbox Drive Shaft Assembly
Part Number: 26111227283
$1086.09 MSRP: $1359.28
You Save: $273.19 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Drive Shaft Assy Five Speed Gearbox; Drive Shaft
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1996-1999 BMW 328i | Convertible(E36), Sedan(E36)
View related parts
BMW 328i Automatic Gearbox Drive Shaft
Part Number: 26107633661
$1358.46 MSRP: $1777.44
You Save: $418.98 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Drive Shaft Gearbox; Drive Shaft, Drive Shaft Assembly
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2012-2016 BMW 328i | N20 Engine(F30), N26 Engine(F30), Sedan N20 Engine(F30), Sedan N26 Engine(F30), Wagon(F31)
View related parts
BMW 328i Rear Drive Shaft
Part Number: 26107551199
$1426.39 MSRP: $1866.32
You Save: $439.93 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Drive Shaft Gearbox; Drive Shaft
- Position: Rear
- Replaces: 26-10-7-527-355
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2007-2013 BMW 328i | Convertible N51 Engine(E93), Convertible N52 Engine(E93), Coupe N51 Engine(E92), Coupe N52 Engine(E92), Sedan N51 Engine(E90), Sedan N52 Engine(E90), Wagon(E91)
View related parts
BMW 328i Rear Drive Shaft
Part Number: 26107551207
$1426.39 MSRP: $1866.32
You Save: $439.93 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manual Drive Shaft Gearbox; Drive Shaft
- Position: Rear
- Replaces: 26-10-7-531-310
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2009-2013 BMW 328i | Coupe N52 Engine(E92), Sedan N52 Engine(E90), Wagon(E91)
View related parts
BMW 328i Automatic Gearbox Drive Shaft
Part Number: 26111227612
$1036.61 MSRP: $1297.35
You Save: $260.74 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Drive Shaft Gearbox; Drive Shaft
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1996-1999 BMW 328i | Convertible(E36), Sedan(E36)
View related parts
BMW 328i Five Speed Gearbox Drive Shaft Assembly
Part Number: 26111229560
$1299.83 MSRP: $1626.78
You Save: $326.95 (21%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Drive Shaft Assy Five Speed Gearbox; Drive Shaft
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1999-2000 BMW 328i | Sedan(E46)
View related parts
BMW 328i Drive Shaft
Part Number: 26107616047
$1358.46 MSRP: $1777.44
You Save: $418.98 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Manual Drive Shaft Gearbox
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2012-2016 BMW 328i | N20 Engine(F30), Sedan N20 Engine(F30), Wagon(F31)
View related parts
BMW 328i Drive Shaft
Part Number: 26107572907
$1426.39 MSRP: $1866.32
You Save: $439.93 (24%)
Product Specifications
- Other Name: Manual Drive Shaft Gearbox
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2007-2013 BMW 328i | Convertible N51 Engine(E93), Convertible N52 Engine(E93), Coupe N51 Engine(E92), Coupe N52 Engine(E92), Sedan N51 Engine(E90), Sedan N52 Engine(E90), Wagon(E91)

BMW 328i Drive Shaft

BMW 328i Drive Shaft is a known and efficient part that is a central part of the car's power train where it transfers power and torque from the gearbox to the differential for better and secure efficiency of the car. Carefully constructed, the Drive Shaft incorporates two u-joints, in the fact that, as it is the motion that is required between the power plant and the differential; it also haves to have a balanced movement to avoid creating vibrations. This reliability is especially apparent from generation to generation of the BMW 328i, such as the E36, E46, E90, and F30 groups, each requiring distinct Drive Shaft designs depending on the cars' construction. BMW 328i Drive Shaft not only plays a role in supporting the performance of the vehicle but also participates in the perception of the sensation for driving by providing a clean delivering of the power in models offered with BMW's TwinPower Turbo system. Also, Drive Shaft calls for all wheel drive systems which improves on traction and stability in difficult terrains, gives it a plus on the road. The BMW 328i Drive Shaft is built and engineered to be sturdy while meeting all the requisite specifications and features; this makes it the epitome of the company's quality and performance, thus adequately satisfying the expectations of drivers. In a nutshell, the BMW 328i Drive Shaft epitomizes the brand's commitment to creating exquisite automobiles that are both effective and secure.

If you are looking for OEM BMW 328i Drive Shaft, we highly recommend to shop with us. Not only do we offer budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW 328i Drive Shaft that come backed by the manufacturer's warranty.

BMW 328i Drive Shaft Parts Questions & Experts Answers

Rear Drive Shaft
26107551199
Q: How to remove the rear and front driveshaft on BMW 328i?
A:
To remove the rear driveshaft, block the front wheels and raise the rear of the vehicle on jackstands. Remove the exhaust system and heat shield, and if necessary, unbolt the exhaust system mounting bracket. Make alignment marks between the shaft, transmission flange, and rubber coupling. Loosen and remove the nuts and bolts securing the coupling to the transmission. Make alignment marks between the driveshaft and differential flange, then unscrew the bolts securing the driveshaft to the rear differential. With the assistance of an assistant, support the driveshaft and unscrew the center support bearing bracket retaining bolts. Lower the center of the shaft and disengage it from the transmission and rear differential. Remove the shaft from underneath the vehicle. Inspect the rubber coupling, support bearing shaft, and universal joints. Inspect the transmission flange locating pin and driveshaft bushing for signs of wear or damage. Replace any worn or damaged parts. Rotate the support bearing to check for smooth turning and replace if difficult or gritty. Apply moly-based lubricant grease to the transmission pin and shaft bushing, then maneuver the shaft into position. Align the marks made prior to removal and engage the shaft bushing with the transmission and rear differential unit flanges. Install the bearing support bracket retaining bolts, tighten the rear coupling bolts, and install new retaining nuts. Tighten the support bracket bolts. Install the exhaust system. To remove the front driveshaft on AWD models, block the rear wheels and raise the front of the vehicle on jackstands. Remove the engine splash shield and front subframe reinforcement panel if equipped. Make match-marks on the front differential flange and the front of the driveshaft, as well as the rear of the driveshaft and the flange at the transfer case. Remove the bolts securing the driveshaft front yoke to the differential flange, then remove the bolts securing the driveshaft rear flange to the transfer case. Remove the driveshaft from the vehicle. Installation is the reverse of removal, replacing any zinc-plated aluminum bolts.

Related BMW 328i Parts

Browse by Year

2016 Drive Shaft 2015 Drive Shaft 2014 Drive Shaft 2013 Drive Shaft 2012 Drive Shaft 2011 Drive Shaft 2010 Drive Shaft 2009 Drive Shaft 2008 Drive Shaft 2007 Drive Shaft 2000 Drive Shaft 1999 Drive Shaft 1998 Drive Shaft 1997 Drive Shaft 1996 Drive Shaft