How do you remove and install the CKP sensor on BMW 325i?

On 2.0L engines, the CKP sensor has two connected parts: the connector housing mounted above the starter and the sensor end which is mounted underneath the starter and behind the flywheel. Remove the starter. Disconnect the electrical connector to the CKP housing, then remove the housing bolt. Working through the starter opening, remove the sensor mounting bolt and pull the sensor from the crankcase. Installation is the reverse of removal, making sure that the guide pin on the CKP sensor is inserted in the guiding groove on the crankcase. On 3.0L engine models, the CKP sensor is located below the starter motor. For access, remove the intake manifold. Disconnect the sensor electrical connector, then remove the retaining bolt and the sensor. Note: The retaining bolt is aluminum, and must be replaced. Check the condition of the sealing ring and replace if necessary. Install the sensor and tighten the new retaining bolt to the specified torque. Installation is the reverse of removal.

Genuine BMW 325i Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Series

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Crankshaft Position Sensors found

View related parts
BMW 325i Pulse Generator, Crankshaft / Gearbox
Part Number: 13627525015
$119.68 MSRP: $175.17
You Save: $55.49 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulse generator, crankshaft/gearbox; Crankshaft Position Sensor, Crankshaft Sensor
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 325i | Sedan(E90)
View related parts
BMW 325i Crankshaft Position Sensor
Part Number: 12141720856
$164.24 MSRP: $217.84
You Save: $53.60 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulse Generator; Igniter
- Replaces: 12-14-1-713-007, 12-14-1-720-852
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1987-1992 BMW 325i | Convertible(E30), Coupe(E30), Sedan(E30)
View related parts
BMW 325i Crankshaft Position Sensor
Part Number: 12141720852
$164.24 MSRP: $217.84
You Save: $53.60 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulse Generator
- Replaced by: 12141720856
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1987-1992 BMW 325i | Convertible(E30), Coupe(E30), Sedan(E30)
View related parts
BMW 325i Crankshaft Position Sensor
Part Number: 12121722570
$203.39 MSRP: $269.78
You Save: $66.39 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulse Generator; Hall Effect Switch, Igniter
- Replaces: 12-12-1-722-587, 12-12-1-717-373
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1987-1992 BMW 325i | Convertible(E30), Coupe(E30), Sedan(E30)
View related parts
BMW 325i Crankshaft Position Sensor
Part Number: 12121722587
$203.39 MSRP: $269.78
You Save: $66.39 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulse Generator
- Replaced by: 12121722570
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1987-1992 BMW 325i | Convertible(E30), Coupe(E30), Sedan(E30)
View related parts
BMW 325i Crankshaft Position Sensor
Part Number: 12141726065
$188.09 MSRP: $249.48
You Save: $61.39 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulse Generator
- Replaces: 12-14-1-726-066
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1992-1995 BMW 325i | Convertible(E36), Sedan(E36)
View related parts
BMW 325i Crankshaft Position Sensor
Part Number: 12141726066
$188.09 MSRP: $249.48
You Save: $61.39 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pulse Generator
- Replaced by: 12141726065
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1992-1995 BMW 325i | Convertible(E36), Sedan(E36)
View related parts
BMW 325i Crankshaft Position Sensor
Part Number: 12141709616
$165.99 MSRP: $220.17
You Save: $54.18 (25%)
Product Specifications
- Other Name: Pulse Generator, Crankshaft; Crankshaft Sensor
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2005 BMW 325i | Sedan M54 Engine(E46), Sedan M56 Engine(E46), Sedan(E46), Wagon M54 Engine(E46), Wagon M56 Engine(E46), Wagon(E46)

BMW 325i Crankshaft Position Sensor

The 325i Crankshaft Position Sensor is an important electrical part that has a very profound impact on the dependability as well as efficiency of 325i cars. This Crankshaft Position Sensor accurately watches the engine phase and sends correct impulses to the EMS, which is very sensitive for controlling the fuel injection and ignition time; otherwise, it is too sensitive to control the different parameters regarding the engines. Located near the engine, the BMW 325i Crankshaft Position Sensor is durable and helps regulate the engine's functions by avoiding possible starting problems that can be caused by the sensor. Fitted for a wide range of 325i models, one of this sensor's primary functions is to enhance the operating characteristics and safety of the vehicle, which is why it is appreciated by fans of BMW. The types of Crankshaft Position Sensor are the inductive and the Hall effect sensors; each type is intended to meet certain performance requirements while engineered to have minimal failure rates. The effect of raising the overall driving experience is supported well enough by the BMW 325i's specifications, including a 3.0 liter six-cylinder engine and safety features which include an anti-lock brake system and dual airbags. The Crankshaft Position Sensor product offers the automotive market a very vital component in the BMW 325i since it helps in the proper operation of a vehicle's engine; thus, for those who wish to have a BMW 325i that is reliable and performs well, this part should be a priority.

If you are looking for OEM BMW 325i Crankshaft Position Sensor, we highly recommend to shop with us. Not only do we offer budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW 325i Crankshaft Position Sensor that come backed by the manufacturer's warranty.

BMW 325i Crankshaft Position Sensor Parts Questions & Experts Answers

Pulse Generator, Crankshaft / Gearbox
13627525015
Q: How do you remove and install the CKP sensor on BMW 325i?
A:
On 2.0L engines, the CKP sensor has two connected parts: the connector housing mounted above the starter and the sensor end which is mounted underneath the starter and behind the flywheel. Remove the starter. Disconnect the electrical connector to the CKP housing, then remove the housing bolt. Working through the starter opening, remove the sensor mounting bolt and pull the sensor from the crankcase. Installation is the reverse of removal, making sure that the guide pin on the CKP sensor is inserted in the guiding groove on the crankcase. On 3.0L engine models, the CKP sensor is located below the starter motor. For access, remove the intake manifold. Disconnect the sensor electrical connector, then remove the retaining bolt and the sensor. Note: The retaining bolt is aluminum, and must be replaced. Check the condition of the sealing ring and replace if necessary. Install the sensor and tighten the new retaining bolt to the specified torque. Installation is the reverse of removal.