×
- Hello
- Login or Register
- Quick Links
- Live Chat
- Track Order
- Parts Availability
- RMA
- Help Center
- Contact Us
- Shop for
- BMW Parts
- BMW Accessories
My Garage
My Account
Cart
Genuine BMW Z3 Blower Motor
A/C Heater Blower Motor- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orSeries
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Blower Motors found
BMW Z3 Blower Unit
Part Number: 64111370930$677.20 MSRP: $835.43You Save: $158.23 (19%)Ships in 1-3 Business Days
BMW Z3 Blower Unit
Part Number: 64111373766$553.22 MSRP: $682.49You Save: $129.27 (19%)Ships in 1-3 Business Days
BMW Z3 Blower Motor
BMW Z3 Blower Motor is responsible for forcing the heated or cooled air through the HVAC ducting to provide occupants with the desired temperature quickly. The Blower Motor performs this task by spinning a multi-speed fan that is mounted in the ventilation housing. In every BMW roadster or coupe in the Z3 line, there stands a single Blower Motor in front of the dash connected to an electronic control module and some easily accessible knobs that allow drivers to immediately adjust fan speed to clear foggy glass on frosty mornings or blast cool air after being parked in a hot parking lot. The module pulses voltage to the Blower Motor. Factory BMW wiring carries that energy, and the fan obeys each change without delay. Unlike larger SUVs that sometimes utilize two motors for their power, the Z3 family has one consistent design, so changes are small, consisting mostly of minor updates in connector shape from year to year while the overall size and mounting remain the same. When the module, wiring, or controls give out, the Blower Motor may run only at a single speed or may quit altogether, which alerts owners to install genuine BMW parts and restore full Z3 comfort.
If you are looking for OEM BMW Z3 Blower Motor, we highly recommend to shop with us. Not only do we offer budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW Z3 Blower Motor that come backed by the manufacturer's warranty.
BMW Z3 Blower Motor Parts Questions & Experts Answers
- Q:How can the blower motor be accessed and installed on BMW Z3?Posted by Parker H.A:To access the blower on E30 models, you will have to remove a cover at the top of the firewall in the engine compartment. For this, remove the negative Battery Cable and pull off the motor cover from its rubber weather strip by cutting wire ties, removing bolts unscrewing and pulling that cover aside. The retaining straps should then be released so as to take out the blower cover. Disconnect two electrical connectors and unease a clamper that hold it in place. After that, simply lift out motor/fan assembly, being careful not to damage a flap below it. To install it all back, put fan and motor into heater and secure with a clamp. Next you need to connect wires and fix fan cover attaching straps onto it. Install outside cover which was already prepared or bolted in position again tying up with wire fixing fasteners as well as weather-striping. At last, reconnect negative battery cable for both E36 models.Remove electrical duct screws inside air intake cowl plus releasing clips of blower cover.Turn ignition switch off then remove air intake cowl-weather-stripping Gently pry out grille.Remove screws holding electrical duct inside air intake cowl.Remove screws holding right side of air intake cowl plus screw holding left side.Pull cowl up from above For M50 equipped vehicles remove injector plate-cover valve cladding.Disconnect unit plugs of control unit housing; moreover, taking away screws out of injector plug plates also disconnecting control cables internally within manufacturer's housing.Unclip heater blower covers along with disconnection wiring attached to motors.Undo sections' clips found above left flaps before you take them off.To install if they were removed blower fans for replacement must be fitted such that their drive pins are correctly placed into indents given there on color dot matches.Put fan into brace thereby connecting wires thereafter clip blower covers instead.Whereas on m50 equipped vehicles connect control cables insert injector plug plates then connect control unit plugs; finally install control unit housing cover. For injector covers, put valve cover cladding and injectors back in place. And now fasten the air intake cowl using screws, put back electrical duct screws and intake grill, so as to mount weather-stripping.Answered by BMW Parts Specialist Adrian / Jun 23, 2026
