How to remove and install the Camshaft Position Sensor on the BMW 328i?

Unfasten the air intake duct mounting bolts and detach the duct. The air hose should be disconnected as the duct is being removed. In front of their respective camshaft ends, you will find that a CMP sensor is placed on each side of the cylinder head. Ensure that ignition has been turned off. Press together locking lugs and pull off sensor wiring plug. At this point, depress clip and separate connector for electrical power to CMP sensor. To remove Sensor loosen bolt retaining it in place. Find seal and recover it by removing screwdriver from its location at the end of fixing bolt connections where it attaches itself onto sealing surface (when required). Replace seal if necessary or damaged. It's just like putting back old things in place after getting out new ones for an exchange before putting them back again.

Genuine BMW 328i Camshaft Position Sensor

Cam Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Series

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Camshaft Position Sensors found

View related parts
BMW 328i Camshaft Position Sensor
Part Number: 12147539165
$156.37 MSRP: $228.86
You Save: $72.49 (32%)
ADD TO CART
Product Specifications
- Other Name: Camshaft Sensor
- Replaces: 12-14-1-435-350, 12-14-1-438-081
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1999-2000 BMW 328i | Sedan(E46)
View related parts
BMW 328i Camshaft Position Sensor
Part Number: 13627525014
$115.92 MSRP: $166.83
You Save: $50.91 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Sensor; M.A.P. Sensor, Pulsator
- Replaces: 13-62-7-546-660, 13-62-7-558-518
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2007-2016 BMW 328i | Convertible N51 Engine(E93), Convertible N52 Engine(E93), Coupe N51 Engine(E92), Coupe N52 Engine(E92), N20 Engine(F30), N26 Engine(F30), Sedan N20 Engine(F30), Sedan N26 Engine(F30), Sedan N51 Engine(E90), Sedan N52 Engine(E90), Wagon(E91), Wagon(F31)
View related parts
BMW 328i Camshaft Position Sensor Compatible
Part Number: 12147518628
$115.92 MSRP: $166.83
You Save: $50.91 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Sensor; Camshaft Position Sensor
- Replaces: 12-14-7-506-273
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1999-2000 BMW 328i | Sedan(E46)
View related parts
BMW 328i Camshaft Position Sensor
Part Number: 13627633958
$115.92 MSRP: $166.83
You Save: $50.91 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Sensor
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2012-2016 BMW 328i | N20 Engine(F30), N26 Engine(F30), Sedan N26 Engine(F30)
View related parts
BMW 328i Camshaft Position Sensor
Part Number: 12141703221
Product Specifications
- Other Name: Camshaft Sensor
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1996-1999 BMW 328i | Convertible(E36), Sedan(E36)

BMW 328i Camshaft Position Sensor

The BMW 328i Camshaft Position Sensor helps keep engine timing in order. It sends camshaft position data to the engine control module so fuel injection and ignition occur at the right moment. So the fuel injection and ignition vary in just the right order to get your car running. With the help of the Camshaft Position Sensor, the ECM controls sequential injectors according to the four-stroke cycle to avoid misfire, which may stall the engine during an exciting drive. To ensure the pistons and valves remain coordinated with the crank sensor, every BMW 328i model relies on this little electronic eye mounted either above the camshaft, behind the cylinder head, or near the engine block. In earlier versions of the BMW 328i, the Camshaft Position Sensor was installed at the back of the head, but people indicate that later models had it placed nearer the front for quicker signals; yet the core Hall-effect design remained the same overall. The Camshaft Position Sensor works alongside the crank sensor to deliver the engine RPM data the dashboard requires, making it one of the two highly critical sensors in any BMW 328i powerplant. The Camshaft Position Sensor is essential for optimal performance.

If you are looking for OEM BMW 328i Camshaft Position Sensor, we highly recommend to shop with us. Not only do we offer budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW 328i Camshaft Position Sensor that come backed by the manufacturer's warranty.

BMW 328i Camshaft Position Sensor Parts Questions & Experts Answers

Camshaft Position Sensor
13627525014
Q: How to remove and install the Camshaft Position Sensor on the BMW 328i?
A:
Unfasten the air intake duct mounting bolts and detach the duct. The air hose should be disconnected as the duct is being removed. In front of their respective camshaft ends, you will find that a CMP sensor is placed on each side of the cylinder head. Ensure that ignition has been turned off. Press together locking lugs and pull off sensor wiring plug. At this point, depress clip and separate connector for electrical power to CMP sensor. To remove Sensor loosen bolt retaining it in place. Find seal and recover it by removing screwdriver from its location at the end of fixing bolt connections where it attaches itself onto sealing surface (when required). Replace seal if necessary or damaged. It's just like putting back old things in place after getting out new ones for an exchange before putting them back again.