How to install a new steering column on BMW 328i?

New steering column shear-bolts and an intermediate shaft clamp bolt/nut will be required upon installation. Start by disconnecting the negative battery cable. Then, remove the three Torx bolts and the driver's knee bolster panel below the steering wheel, disconnecting any electrical connectors as needed. Reach behind the instrument panel to pull down the driver's side footwell heating duct and release the wiring harness from it. Extend the steering wheel fully, set it to the lowest position, and remove it. Using a blunt, flat-bladed tool, pry the column upper cover from the lower one. With the column at its highest position, press the retaining clips on each side and pull down the lower column cover. Disconnect electrical connectors from the column switches and release the harness from its retaining clips on the column. Slide up the rubber boot at the base of the column, remove the clamp bolt from the shaft and discard it. Then, remove the four column mounting bolts/nuts, pulling the column to the rear. Before reinstalling, inspect the column for safety features, potential damages, and check for freeplay in the column bushings. Any overhaul needed should be done by a BMW dealer. When installing, position the column and align it with the intermediate shaft splines. Secure it using the mounting bolts, reconnect electrical connectors, and ensure wiring is properly routed. Align the intermediate shaft with column marks, insert the column into the shaft, and secure with the new clamp bolt. Reattach the rubber boot, steering column covers, and steering wheel. Finally, reposition the footwell air duct, reconnect the negative battery cable, and if a new column has been placed, recalibrate the steering angle sensor using BMW diagnostic tools, preferably through a qualified dealer or shop.

Genuine BMW 328i Steering Column

Steering Column Tilt

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Series

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Steering Columns found

View related parts
BMW 328i Manually Adjust. Steering Column
Part Number: 32306858559
$930.56 MSRP: $1147.99
You Save: $217.43 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Column Assembly, Steering Column
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2012-2016 BMW 328i | N20 Engine(F30), N26 Engine(F30), Sedan N20 Engine(F30), Sedan N26 Engine(F30), Wagon(F31)
View related parts
BMW 328i Manually Adjust. Steering Column
Part Number: 32306854045
$930.56 MSRP: $1147.99
You Save: $217.43 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Column Assembly, Steering Column
- Replaces: 32-30-6-787-326
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2012-2015 BMW 328i | N20 Engine(F30), N26 Engine(F30), Sedan N20 Engine(F30), Sedan N26 Engine(F30)
View related parts
BMW 328i Manually Adjust. Steering Column
Part Number: 32303450159
$1047.90 MSRP: $1350.63
You Save: $302.73 (23%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Column Assembly, Steering Column
- Replaces: 32-30-1-094-661, 32-30-6-751-670, 32-30-1-097-024, 32-30-6-764-004
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1999-2000 BMW 328i | Sedan(E46)
View related parts
BMW 328i Manually Adjust. Steering Column
Part Number: 32306780274
$790.98 MSRP: $975.80
You Save: $184.82 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Column Assembly, Steering Column
- Replaces: 32-30-6-774-268
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2007-2013 BMW 328i | Convertible N51 Engine(E93), Convertible N52 Engine(E93), Coupe N51 Engine(E92), Coupe N52 Engine(E92), Sedan N51 Engine(E90), Sedan N52 Engine(E90), Wagon(E91)
View related parts
BMW 328i Manually Adjust. Steering Column
Part Number: 32303450160
$1043.74 MSRP: $1345.27
You Save: $301.53 (23%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Column Assembly, Steering Column
- Replaces: 32-30-1-097-026, 32-30-6-764-005, 32-30-6-751-672, 32-30-1-094-663
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 1999-2000 BMW 328i | Sedan(E46)
View related parts
BMW 328i Manually Adjust. Steering Column
Part Number: 32306786899
$870.09 MSRP: $1073.39
You Save: $203.30 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Column Assembly, Steering Column
- Replaces: 32-30-6-782-763, 32-30-6-783-606, 32-30-6-780-272, 32-30-6-772-273, 32-30-6-770-886
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2007-2011 BMW 328i | Coupe N51 Engine(E92), Coupe N52 Engine(E92), Sedan N51 Engine(E90), Sedan N52 Engine(E90), Wagon(E91)

BMW 328i Steering Column

The BMW 328i Steering Column serves as the essential bridge between the wheel in your hands and the steering gear, letting the car answer instantly to every turn. Running down from the wheel, the Steering Column transmits angle and torque with precision, but it also houses the ignition lock and anti theft features first seen industry wide in the late sixties. In every 328i generation, the BMW Steering Column uses a collapsible shaft held by a tolerance ring so it can absorb crash energy instead of sending force toward the driver. Universal joints at the lower shaft give flexibility in steering rack placement while keeping smooth motion, and they guide column movement during frontal impacts. Later BMW 328i models introduced quick manual height and reach adjustment, letting different drivers dial in comfort without losing rigidity. Earlier cars relied on fixed geometry, so the adjustable style is the main evolution, and this marks the big distinction between past and present Steering Column layouts. Regardless of year, each BMW 328i benefits when the Steering Column locks firmly at center without squeaks or rough spots, warning drivers to replace the unit if any play or noise appears.

If you are looking for OEM BMW 328i Steering Column, we highly recommend to shop with us. Not only do we offer budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW 328i Steering Column that come backed by the manufacturer's warranty.

BMW 328i Steering Column Parts Questions & Experts Answers

Manually Adjust. Steering Column
32306780274
Q:
How to install a new steering column on BMW 328i?
Posted by Mathew M.
A:
New steering column shear-bolts and an intermediate shaft clamp bolt/nut will be required upon installation. Start by disconnecting the negative battery cable. Then, remove the three Torx bolts and the driver's knee bolster panel below the Steering Wheel, disconnecting any electrical connectors as needed. Reach behind the instrument panel to pull down the driver's side footwell heating duct and release the wiring harness from it. Extend the steering wheel fully, set it to the lowest position, and remove it. Using a blunt, flat-bladed tool, pry the column upper cover from the lower one. With the column at its highest position, press the retaining clips on each side and pull down the lower column cover. Disconnect electrical connectors from the column switches and release the harness from its retaining clips on the column. Slide up the rubber boot at the base of the column, remove the clamp bolt from the shaft and discard it. Then, remove the four column mounting bolts/nuts, pulling the column to the rear. Before reinstalling, inspect the column for safety features, potential damages, and check for freeplay in the column bushings. Any overhaul needed should be done by a BMW dealer. When installing, position the column and align it with the intermediate shaft splines. Secure it using the mounting bolts, reconnect electrical connectors, and ensure wiring is properly routed. Align the intermediate shaft with column marks, insert the column into the shaft, and secure with the new clamp bolt. Reattach the rubber boot, steering column covers, and steering wheel. Finally, reposition the footwell air duct, reconnect the negative battery cable, and if a new column has been placed, recalibrate the steering angle sensor using BMW diagnostic tools, preferably through a qualified dealer or shop.
Answered by BMW Parts Specialist Brandon / Feb 26, 2022