How to disconnect and remove the intake manifold in six cylinder engine on BMW X5?

Remove the battery negative cable in the cargo compartment and always make sure to read the battery disconnection cautions before doing it. In the engine compartment, first take out the venting micro filter and the plenum cover and then snap off the plenum seal and separate the plenum bulk head also. Remove the live terminal B+ at the plenum cover from the left and then pull the upper engine covers off. While above the engine remove the B+ lead bracket, resonance valve electrical connector, oxygen sensor connectors, electrical connector for intake air temperature sensor, manifold vacuum line and mark the oxygen sensor connectors for reassembly. Situated at the left side of the cylinder head, disconnect the engine vent hose from the cylinder head cover, squeezing the spring clips besides, pull the VANOS solenoid connector loose. The fuel injector electrical connectors have to be disconnected from the injectors by pulling one corner of the wire lock clip on each injector's connector with a small screwdriver, then by releasing the two main harness hold-down connectors and lifting the fuel injector harness entirely. On the left-hand side and below the intake manifold you need to disconnect at the fuel tank venting valve, then remove the hose from the quick disconnect fitting, and finally unbolt and remove the valve from the manifold. Loosen the nut of the electrical connector of the idle speed control valve and then remove the throttle housing. Twist of the Schrader valve cap on the fuel rail, relief from pressure by unscrewing the fuel tank cap and using a short blast a compressed air to force fuel back into the tank. At the rear of the manifold to sever the fuel supply line from the fuel rail use a special tool to press the locking clip located in the end the of the fuel line fitting. Below the vehicle, you require loosening of the lower intake manifold support mounting bolt which is close to the left engine mount after which you loosen the knock sensor connector that is usually fixed at the base of the manifold and finally remove the manifold lower support nuts and the intake manifold mounting nuts. Gently take off the intake manifold from the cylinder head being over watchful not to entangle any of the electrical connection or hoses. The reinstallation of the intake manifold is in a sense the inverse of the removal with new fuel injector seals and with careful examination of the condition of the intake manifold gaskets and the rubber sealing at the throttle house and the idle speed control valve as well as the O-ring seal between the mass air flow sensor and the air filter housing; the O-ring is coated with assembly fluids in preparation for reassembly. On reconnecting the throttle assembly harness connector, the arrow depicted on the connector should merge with that on the plug when tightened.

Genuine BMW X5 Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Series

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

25 Intake Manifolds found

View related parts
BMW X5 Intake Manifold With Flap Control
Part Number: 11617823073
$1054.27 MSRP: $1379.42
You Save: $325.15 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 11618519140
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2009-2013 BMW X5 | xDrive35d(E70)
View related parts
BMW X5 Intake Manifold System
Part Number: 11618601612
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Replaced by: 11615B3F936
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2019-2020 BMW X5 | M50i(G05), xDrive50i(G05)
View related parts
BMW X5 Intake Manifold System
Part Number: 11617588126
$660.45 MSRP: $864.15
You Save: $203.70 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2016-2018 BMW X5 | xDrive40e(F15)
View related parts
BMW X5 Intake Manifold System
Part Number: 11618601613
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Replaced by: 11615B3F937
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2019-2020 BMW X5 | M50i(G05), xDrive50i(G05)
View related parts
BMW X5 Intake Manifold With Flap Control
Part Number: 11618514731
$1279.64 MSRP: $1674.30
You Save: $394.66 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2014-2018 BMW X5 | xDrive35d(F15)
View related parts
BMW X5 Intake Manifold System
Part Number: 11617537882
$2824.84 MSRP: $3696.08
You Save: $871.24 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Replaces: 11-61-7-529-667, 11-61-4-483-891, 11-61-4-483-890, 11-61-1-438-783
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2004-2006 BMW X5 | 4.4i(E53), 4.8is(E53)
View related parts
BMW X5 Intake Manifold System
Part Number: 11617555663
$743.02 MSRP: $972.18
You Save: $229.16 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2011-2013 BMW X5 | xDrive50i(E70)
View related parts
BMW X5 Intake Manifold System
Part Number: 11617555666
$743.02 MSRP: $972.18
You Save: $229.16 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2011-2013 BMW X5 | xDrive50i(E70)
View related parts
BMW X5 Intake Manifold
Part Number: 11617559523
$825.57 MSRP: $1080.20
You Save: $254.63 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 11-61-7-522-927
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2007-2010 BMW X5 | 3.0si(E70), xDrive30i(E70)
View related parts
BMW X5 INTAKE MANIFOLD SYSTEM
Part Number: 11615B3F937
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Position: Driver Side
- Replaces: 11-61-8-601-613
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2021-2023 BMW X5 | 6 Cyl 3.0 L GAS, 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV), 8 Cyl 4.4 L GAS
View related parts
BMW X5 INTAKE SYSTEM WITH CHARGE AI
Part Number: 11617952861
$1516.99 MSRP: $1984.86
You Save: $467.87 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2024 BMW X5 | 6 Cyl 3.0 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV), 8 Cyl 4.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
BMW X5 Intake Manifold
Part Number: 13711437100
$175.31 MSRP: $212.60
You Save: $37.29 (18%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Duct
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2006 BMW X5 | 3.0i(E53)
View related parts
BMW X5 Intake Manifold
Part Number: 11617525753
$533.05 MSRP: $639.33
You Save: $106.28 (17%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 11-61-7-502-274
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2006 BMW X5 | 3.0i(E53)
View related parts
BMW X5 INTAKE MANIFOLD SYSTEM
Part Number: 11615B3F932
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Position: Passenger Side
- Replaced by: 11615B3F938
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2024 BMW X5 | 6 Cyl 3.0 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV), 8 Cyl 4.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
BMW X5 INTAKE MANIFOLD SYSTEM
Part Number: 11615B3F933
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Position: Driver Side
- Replaced by: 11615B3F939
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2024 BMW X5 | 6 Cyl 3.0 L MILD HYBRID EV-GAS (MHEV), 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV), 8 Cyl 4.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
BMW X5 INTAKE MANIFOLD SYSTEM
Part Number: 11615B3F936
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Position: Passenger Side
- Replaces: 11-61-8-601-612
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2021-2023 BMW X5 | 6 Cyl 3.0 L GAS, 6 Cyl 3.0 L PLUG-IN HYBRID EV-GAS (PHEV), 8 Cyl 4.4 L GAS
View related parts
BMW X5 Intake Manifold System
Part Number: 11617601432
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2014-2018 BMW X5 | xDrive50i(F15)
View related parts
BMW X5 Intake Manifold System
Part Number: 11617601434
$891.60 MSRP: $1166.59
You Save: $274.99 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Position: Driver Side
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2014-2018 BMW X5 | xDrive50i(F15)
View related parts
BMW X5 Intake Manifold System
Part Number: 11617576911
$990.68 MSRP: $1296.23
You Save: $305.55 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2011-2018 BMW X5 | sDrive35i(F15), xDrive35i(E70), xDrive35i(F15)
View related parts
BMW X5 Intake Manifold System
Part Number: 11617531618
$2823.42 MSRP: $3694.23
You Save: $870.81 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Intake Manifold
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2007-2010 BMW X5 | 4.8i(E70), xDrive48i(E70)

| Page 1 of 2 |Next >

1-20 of 25 Results

BMW X5 Intake Manifold

If you are looking for OEM BMW X5 Intake Manifold, we highly recommend to shop with us. Not only do we offer budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW X5 Intake Manifold that come backed by the manufacturer's warranty.

BMW X5 Intake Manifold Parts Questions & Experts Answers

Intake Manifold
11617525753
Q: How to disconnect and remove the intake manifold in six cylinder engine on BMW X5?
A:
Remove the battery negative cable in the cargo compartment and always make sure to read the battery disconnection cautions before doing it. In the engine compartment, first take out the venting micro filter and the plenum cover and then snap off the plenum seal and separate the plenum bulk head also. Remove the live terminal B+ at the plenum cover from the left and then pull the upper engine covers off. While above the engine remove the B+ lead bracket, resonance valve electrical connector, oxygen sensor connectors, electrical connector for intake air temperature sensor, manifold vacuum line and mark the oxygen sensor connectors for reassembly. Situated at the left side of the cylinder head, disconnect the engine vent hose from the cylinder head cover, squeezing the spring clips besides, pull the VANOS solenoid connector loose. The fuel injector electrical connectors have to be disconnected from the injectors by pulling one corner of the wire lock clip on each injector's connector with a small screwdriver, then by releasing the two main harness hold-down connectors and lifting the fuel injector harness entirely. On the left-hand side and below the intake manifold you need to disconnect at the fuel tank venting valve, then remove the hose from the quick disconnect fitting, and finally unbolt and remove the valve from the manifold. Loosen the nut of the electrical connector of the idle speed control valve and then remove the throttle housing. Twist of the Schrader valve cap on the Fuel Rail, relief from pressure by unscrewing the fuel tank cap and using a short blast a compressed air to force fuel back into the tank. At the rear of the manifold to sever the fuel supply line from the fuel rail use a special tool to press the locking clip located in the end the of the fuel line fitting. Below the vehicle, you require loosening of the lower intake manifold support mounting bolt which is close to the left engine mount after which you loosen the knock sensor connector that is usually fixed at the base of the manifold and finally remove the manifold lower support nuts and the intake manifold mounting nuts. Gently take off the intake manifold from the cylinder head being over watchful not to entangle any of the electrical connection or hoses. The reinstallation of the intake manifold is in a sense the inverse of the removal with new fuel injector seals and with careful examination of the condition of the intake manifold gaskets and the rubber sealing at the throttle house and the idle speed control valve as well as the O-ring seal between the Mass Air Flow Sensor and the air filter housing; the O-ring is coated with assembly fluids in preparation for reassembly. On reconnecting the throttle assembly harness connector, the arrow depicted on the connector should merge with that on the plug when tightened.

Genuine BMW X5 Intake Manifold

25 Intake Manifolds found

BMW X5 Intake Manifold With Flap Control

BMW X5 Intake Manifold System

BMW X5 Intake Manifold System

BMW X5 Intake Manifold System

BMW X5 Intake Manifold With Flap Control

BMW X5 Intake Manifold System

BMW X5 Intake Manifold System

BMW X5 Intake Manifold System

BMW X5 Intake Manifold

BMW X5 INTAKE MANIFOLD SYSTEM

BMW X5 INTAKE SYSTEM WITH CHARGE AI

BMW X5 Intake Manifold

BMW X5 Intake Manifold

BMW X5 INTAKE MANIFOLD SYSTEM

BMW X5 INTAKE MANIFOLD SYSTEM

BMW X5 INTAKE MANIFOLD SYSTEM

BMW X5 Intake Manifold System

BMW X5 Intake Manifold System

BMW X5 Intake Manifold System

BMW X5 Intake Manifold System

BMW X5 Intake Manifold

BMW X5 Intake Manifold Parts Questions & Experts Answers

Related BMW X5 Parts

Browse by Year