BMW 51247144878 Catch Key

To remove the trunk lid latch, you should first open the trunk, then get rid of plastic expanding rivets and trim panel. Disconnect its electrical connector by unbolting them mounting fasteners, while lifting the latch from the trunk lid as you also separate the cable from lock cylinder. In order to take off the operating cable, a clip must be released, a plastic outer cable fitting be slid-off, and center pin pried up with inner cable end fitting being detached. Taking off the trunk lid lock cylinder entails pulling out lock cylinder from panel after disconnection of operating cables and removal of mounting fasteners. Remove trim panel, reach behind button to squeeze sides towards each other and push out assembly while removing it to disconnect electrical connector; this will help you take away and discard buttons release on key fobs that are damaged or worn-out use new buttons instead To remove tailgate latch pull rear window side trims inwardly so as to unleash retaining clips which hold onto them at upper trim level Take off mounting clips, fold down and remove insert located in tailgate rear panel; open rear window for ease while pulling plastic trim at top of rear panel backwards to release buttresses then detach mount bolts above. Then pry cover loose; unscrew bolt on each side of handle recess; pull back rear trim panel from tailgate - releasing clips - dislocate boot compartment light Removing this requires removal screws sliding which releases an opened when placed into position On other hand if one wants unlocks simply slide away until disconnected disconnects unlinking splitness nail between two neighboring slots Disconnecting it may have some portions inside consoles behind where these parts connect The final step involves unscrewing those fastening attachments provided placing hands behind sides There exist several means access given part: firstly there are four panels that surround exit; secondly its four sides are connected through hinge mechanism Lastly those who manipulate their car keys via electronic devices can find spot under appropriate button where they can insert it For instance, on top - right corner between driver's seat and backrest there is a little flashlight which can be used in case of emergency The reason why so many individuals find themselves without any keys is due to their habits such as leaving them inside bags, pockets or even misplacing them altogether In this case, you will need to move left side dash trim out of place.

To remove the inside door handle, begin by pulling off the inside door trim panel, undoing the interior handle lever, let go of the cable and take off the handle. When removing a front door latch assembly, you will have to remove a window regulator assembly; unplug wiring harnesses, release cables and release rods then loosen and remove the latch. The removal of front door exterior handle involves taking out lock cylinder (if necessary), rear cover and finally disengaging it from attachment. To take away the front door lock cylinder entails accessing then removing a single retaining bolt before pulling it out. In backdoor, start by removing inner trim panel and watershield, unplugging latch wiring, opening rod and opening cable in that order before removing latch assembly. To get rid of rear outer handle on a backdoor remove rear cover as well as pull it outwards while ensuring that latch lever is kept properly positioned. On installation however; you reverse these steps making sure components are properly sealed and secured; check functioning of the latch prior to closing door.

To remove the trunk lid latch, you should first open the trunk, then get rid of plastic expanding rivets and trim panel. Disconnect its electrical connector by unbolting them mounting fasteners, while lifting the latch from the trunk lid as you also separate the cable from lock cylinder. In order to take off the operating cable, a clip must be released, a plastic outer cable fitting be slid-off, and center pin pried up with inner cable end fitting being detached. Taking off the trunk lid lock cylinder entails pulling out lock cylinder from panel after disconnection of operating cables and removal of mounting fasteners. Remove trim panel, reach behind button to squeeze sides towards each other and push out assembly while removing it to disconnect electrical connector; this will help you take away and discard buttons release on key fobs that are damaged or worn-out use new buttons instead To remove tailgate latch pull rear window side trims inwardly so as to unleash retaining clips which hold onto them at upper trim level Take off mounting clips, fold down and remove insert located in tailgate rear panel; open rear window for ease while pulling plastic trim at top of rear panel backwards to release buttresses then detach mount bolts above. Then pry cover loose; unscrew bolt on each side of handle recess; pull back rear trim panel from tailgate - releasing clips - dislocate boot compartment light Removing this requires removal screws sliding which releases an opened when placed into position On other hand if one wants unlocks simply slide away until disconnected disconnects unlinking splitness nail between two neighboring slots Disconnecting it may have some portions inside consoles behind where these parts connect The final step involves unscrewing those fastening attachments provided placing hands behind sides There exist several means access given part: firstly there are four panels that surround exit; secondly its four sides are connected through hinge mechanism Lastly those who manipulate their car keys via electronic devices can find spot under appropriate button where they can insert it For instance, on top - right corner between driver's seat and backrest there is a little flashlight which can be used in case of emergency The reason why so many individuals find themselves without any keys is due to their habits such as leaving them inside bags, pockets or even misplacing them altogether In this case, you will need to move left side dash trim out of place.

To remove the inside door handle, begin by pulling off the inside door trim panel, undoing the interior handle lever, let go of the cable and take off the handle. When removing a front door latch assembly, you will have to remove a window regulator assembly; unplug wiring harnesses, release cables and release rods then loosen and remove the latch. The removal of front door exterior handle involves taking out lock cylinder (if necessary), rear cover and finally disengaging it from attachment. To take away the front door lock cylinder entails accessing then removing a single retaining bolt before pulling it out. In backdoor, start by removing inner trim panel and watershield, unplugging latch wiring, opening rod and opening cable in that order before removing latch assembly. To get rid of rear outer handle on a backdoor remove rear cover as well as pull it outwards while ensuring that latch lever is kept properly positioned. On installation however; you reverse these steps making sure components are properly sealed and secured; check functioning of the latch prior to closing door.

To remove the trunk lid latch, you should first open the trunk, then get rid of plastic expanding rivets and trim panel. Disconnect its electrical connector by unbolting them mounting fasteners, while lifting the latch from the trunk lid as you also separate the cable from lock cylinder. In order to take off the operating cable, a clip must be released, a plastic outer cable fitting be slid-off, and center pin pried up with inner cable end fitting being detached. Taking off the trunk lid lock cylinder entails pulling out lock cylinder from panel after disconnection of operating cables and removal of mounting fasteners. Remove trim panel, reach behind button to squeeze sides towards each other and push out assembly while removing it to disconnect electrical connector; this will help you take away and discard buttons release on key fobs that are damaged or worn-out use new buttons instead To remove tailgate latch pull rear window side trims inwardly so as to unleash retaining clips which hold onto them at upper trim level Take off mounting clips, fold down and remove insert located in tailgate rear panel; open rear window for ease while pulling plastic trim at top of rear panel backwards to release buttresses then detach mount bolts above. Then pry cover loose; unscrew bolt on each side of handle recess; pull back rear trim panel from tailgate - releasing clips - dislocate boot compartment light Removing this requires removal screws sliding which releases an opened when placed into position On other hand if one wants unlocks simply slide away until disconnected disconnects unlinking splitness nail between two neighboring slots Disconnecting it may have some portions inside consoles behind where these parts connect The final step involves unscrewing those fastening attachments provided placing hands behind sides There exist several means access given part: firstly there are four panels that surround exit; secondly its four sides are connected through hinge mechanism Lastly those who manipulate their car keys via electronic devices can find spot under appropriate button where they can insert it For instance, on top - right corner between driver's seat and backrest there is a little flashlight which can be used in case of emergency The reason why so many individuals find themselves without any keys is due to their habits such as leaving them inside bags, pockets or even misplacing them altogether In this case, you will need to move left side dash trim out of place.

Remove the trunk lid trim panel and unclip the trunk lock cylinder trim cover. Working inside the trunk at the rear of the lock cylinder, disconnect the bowden cable from the lock cylinder. Insert a 2 mm diameter punch into the hole and press down the catch, then rotate the lock release 90° counterclockwise and remove the punch. Remove the fasteners and take out the lock cylinder. For installation, reverse the removal process, ensuring to inspect and replace the lock cylinder seal if necessary, properly seat the seal, and rotate the lock release 90° clockwise once the lock is in place.

After removing the interior door trim panel, you need to release the interior handle lever.

Reset comfort access (CA) by disconnecting and reconnecting the battery.