How to replace the crankshaft front and rear oil seals in 3.0L six cylinder engine on BMW 330i?

To change the crankshaft front oil seal, detach the crankshaft vibration damper. To replace the crankshaft rear oil seal, remove the flywheel/driveplate. While the flywheel/driveplate is off, this would be an ideal time to check on your vehicle's manual transmission clutch. Carefully pry out the oil seal from within a cylinder block using a flat-bladed screwdriver or a similar tool. Try as much as possible not to destroy either side of where you have placed it on your engine. Alternatively, drill two tiny opposing holes in the hard outer surface of the sealant, insert two self-tapping screws and use pliers to pull out this particular type of filler material. Before applying any lubrication between crank shaft hub and cylinder block surfaces make sure that they are cleaned up very well with clean engine oil solution. Genuine BMW seal kits come with a guide sleeve pre-fitted into the seals using Loctite sealing compound and primer at place. Set seal and guide sleeve onto crankshaft hub such that slots located at external periphery of sealer are aligned with junction in cylinder block. Apply Loctite primer supplied to both slots on outer sur-face of sealer using brush provided for that purpose only. Make sure you leave it for at least one minute before proceeding forward because most times you may find yourself running after some little mistakes which could have been avoided if enough time was given for drying process. Use right size socket or pipe to push in new oil seal squarely as possible until it becomes flush with its outer edge only then should you stop hammering; also force some Loctite primer into slot on each side of lip by means of brush supplied; inject additional loctite sealing compound by way of kit syringe into slot on each side of lip finally apply some more primer over coating sealing compound. Afterwards fit back crank shaft vibration damper or fly wheel drive plate assembly again return sequence.

Genuine BMW 330i Crankshaft Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Series

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Crankshaft Seals found

View related parts
BMW 330i Front Shaft Seal
Part Number: 11117547842
$37.08 MSRP: $60.88
You Save: $23.80 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal; Crankshaft Seal, Front
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Shaft Seal
Part Number: 11117587168
$35.38 MSRP: $58.10
You Save: $22.72 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Shaft Seal
Part Number: 11118618864
$33.71 MSRP: $55.36
You Save: $21.65 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 11-11-7-636-055, 11-11-7-593-353
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Shaft Seal
Part Number: 11142249533
$91.31 MSRP: $97.36
You Save: $6.05 (7%)
ADD TO CART
Product Specifications
- Other Name: Front Crank Seal, Oil Seal, Rear Main Seal
- Replaces: 11-14-1-706-785, 11-14-2-245-364, 11-14-2-247-164, 11-14-2-193-237, 11-14-1-706-999
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2005 BMW 330i | Sedan(E46)
View related parts
BMW 330i SHAFT SEAL
Part Number: 11148664904
$33.71 MSRP: $55.36
You Save: $21.65 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 11-14-8-602-594
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2021-2024 BMW 330i | 4 Cyl 2.0 L GAS
View related parts
BMW 330i Shaft Seal
Part Number: 11148602594
$33.71 MSRP: $55.36
You Save: $21.65 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 11148664904
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2017-2020 BMW 330i | Sedan(F30), Sedan(G20)
View related parts
BMW 330i Shaft Seal
Part Number: 11118604931
$33.71 MSRP: $55.36
You Save: $21.65 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 11118664905
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2017-2020 BMW 330i | Sedan(F30), Sedan(G20)
View related parts
BMW 330i Shaft Seal
Part Number: 11117584398
$37.08 MSRP: $60.88
You Save: $23.80 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 11-11-7-547-841
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2006 BMW 330i | Sedan(E90)
View related parts
BMW 330i Shaft Seal
Part Number: 11142249532
$91.31 MSRP: $97.36
You Save: $6.05 (7%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2005 BMW 330i | Sedan(E46)
View related parts
BMW 330i Set Of Covers
Part Number: 11141438274
$121.97 MSRP: $167.00
You Save: $45.03 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rear Main Seal, Rear Main Seal Retainer, Retainer
- Replaces: 11-14-1-433-897, 11-14-1-744-158
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2001-2005 BMW 330i | Sedan(E46)
View related parts
BMW 330i SHAFT SEAL
Part Number: 11118664905
$33.71 MSRP: $55.36
You Save: $21.65 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaces: 11-11-8-604-931
- Warranty: This genuine part is guaranteed by BMW's factory warranty.
Fits the following Vehicles:
- 2021-2023 BMW 330i | 4 Cyl 2.0 L GAS

BMW 330i Crankshaft Seal

The BMW 330i Crankshaft Seal is one of the critical parts of a car because it significantly determines the dependability and efficiency of these automobiles. Fitted at the front of the engine, the objective of this Crankshaft Seal is to stop the oil leakage from the crankcase to enable the engine components to be well oiled, hence reduce friction and risks of equipment damage. It goes without saying that the BMW 330i Crankshaft Seal is rather robust, thus it can become a useful part of the 330i car with RWD or AWD. A defective Crankshaft Seal can cause a number of problems including oil leakage which can endanger the efficiency of the vehicle's engine not forgetting the safety of the users. Hence, replacement should be done as soon as possible in order to enhance the efficiency of the BMW 330i and it's durability. The Crankshaft Seal is predominantly made of metal and rubber of superior quality so as to endure the stresses of the functional engine. Also, the BMW 330i Crankshaft Seal plays a part in the feel of the car by keeping the engine running and performing optimally; a critical factor on a car as the 330i that is powered by a turbocharged four-cylinder engine. Because of the effective combination of performance, luxury, and dependability characteristic of BMW, the BMW 330i Crankshaft Seal is exceptional in the automotive industry and is the perfect representation of the marque.

If you are looking for OEM BMW 330i Crankshaft Seal, we highly recommend to shop with us. Not only do we offer budget friendly prices, but we also provide fast delivery. In addition, we have a hassle-free return policy on all genuine BMW 330i Crankshaft Seal that come backed by the manufacturer's warranty.

BMW 330i Crankshaft Seal Parts Questions & Experts Answers

Front Shaft Seal
11117547842
Q: How to replace the crankshaft front and rear oil seals in 3.0L six cylinder engine on BMW 330i?
A:
To change the crankshaft front oil seal, detach the crankshaft vibration damper. To replace the crankshaft rear oil seal, remove the flywheel/driveplate. While the flywheel/driveplate is off, this would be an ideal time to check on your vehicle's manual transmission clutch. Carefully pry out the oil seal from within a cylinder block using a flat-bladed screwdriver or a similar tool. Try as much as possible not to destroy either side of where you have placed it on your engine. Alternatively, drill two tiny opposing holes in the hard outer surface of the sealant, insert two self-tapping screws and use pliers to pull out this particular type of filler material. Before applying any lubrication between crank shaft hub and cylinder block surfaces make sure that they are cleaned up very well with clean engine oil solution. Genuine BMW seal kits come with a guide sleeve pre-fitted into the seals using Loctite sealing compound and primer at place. Set seal and guide sleeve onto crankshaft hub such that slots located at external periphery of sealer are aligned with junction in cylinder block. Apply Loctite primer supplied to both slots on outer sur-face of sealer using brush provided for that purpose only. Make sure you leave it for at least one minute before proceeding forward because most times you may find yourself running after some little mistakes which could have been avoided if enough time was given for drying process. Use right size socket or pipe to push in new oil seal squarely as possible until it becomes flush with its outer edge only then should you stop hammering; also force some Loctite primer into slot on each side of lip by means of brush supplied; inject additional loctite sealing compound by way of kit syringe into slot on each side of lip finally apply some more primer over coating sealing compound. Afterwards fit back crank shaft vibration damper or fly wheel drive plate assembly again return sequence.